Free Roof Pitch Calculator

Free Roof Pitch Calculator

Enter the pitch however you have it — degrees, a ratio, a percentage, or a rise and a run — and get the other three straight back. Then read off the rafter length, the plumb and seat cuts, the roof area, and whether the roofing you want is even allowed to go on at that pitch. Free, no sign-up, works on your phone.

The four ways a pitch gets written down

The same roof gets described four different ways depending on who is talking, and half the confusion on site comes from people quoting different ones at each other.

  • Degrees — what a designer, a council and most New Zealand roofing literature use. A 25° roof.
  • Ratio, rise : 12 — the American convention you will see on imported plans and in a lot of online tables. A 25° roof is 5.6 : 12.
  • Ratio, 1 : run — how fall is usually written for low-pitch and drainage work. A 25° roof is 1 : 2.14.
  • Percent — common in European literature and in civil work. A 25° roof is 46.6%.

Type any one of them into the calculator and it gives you the other three, plus the millimetres of rise per metre of run — which is the number you actually use when you are setting out.

Rafters and cut angles

Give it the span and it works out the run to the ridge, the rise, the common rafter length along the top edge, and the extra along the slope for the eave. The plumb cut and the seat cut come out of the same angle and always add to 90°, so if you set the saw to the pitch for the plumb cut you have the other one for free.

Pick a hip roof and it adds the hip rafter: its own pitch, its run in plan, its length, and the side cut. A hip runs at 45° across the plan, so its run is the common run multiplied by 1.414 — which is why the hip is always flatter than the common rafter on the same roof, and why using the common pitch on a hip gives you a rafter that is far too short.

There is also a birdsmouth check. Cut a seat over a 90 mm plate and the calculator tells you how much rafter is left above the cut, and warns you if that drops under a third of the depth — the usual rule of thumb before someone needs to look at it properly.

Roof area without measuring the roof

The slope factor is 1 ÷ cos(pitch), and it is the most useful number on the page. Multiply any plan area by it and you get the real area of the sloping surface. At 25° it is 1.103, so a 100 m² footprint is 110 m² of roof. Use it for roofing, underlay, battens and labour alike.

Minimum pitch by roofing type

This is the part that catches people out. Roofing is not interchangeable at low pitch: standard corrugate needs 8°, and a flat-looking modern roof is only possible because trapezoidal profiles and membranes go much lower. Drop a corrugate roof to 6° and it is outside the Acceptable Solution, no matter how good it looks.

The Roofing tab checks your pitch against the New Zealand minimums from E2/AS1 and the Metal Roofing Code of Practice — corrugate in its three profile heights, trapezoidal, long-run tray, pressed metal tile, concrete and clay tile, asphalt shingle, slate and membrane.

Treat a tick as “worth asking about”, not as approval. A long run, end-lapped sheets, a high wind zone or heavy rainfall all push the minimum up, and the manufacturer’s own figure for the exact profile always governs. Check the current E2/AS1 and the product literature before you commit.

Building outside New Zealand

This calculator can be used in any country. The pitch conversions, rafter lengths, cut angles and roof areas are plain geometry and work anywhere. Only the minimum pitches on the Roofing tab are local — check your own country’s building codes and the manufacturer’s literature before you start.

Wiesner Enterprises NZ and its owner accept no responsibility for any figure, quantity or drawing this tool produces, or for any decision made on it. Use it at your own discretion. It is not a substitute for a designer, an engineer, a Licensed Building Practitioner or your council. Confirm everything with the right people before you order material or start work.

More free tools

Design tools and calculators for the trades, all free to use.

Stair Calculator

Risers, going, pitch and stringer, checked to D1/AS1

Open the Stair Calculator

Sleepout and Cabin Planner

Size, materials, costs and the consent check

Open the Sleepout Planner

House Planner

Floor plans, elevations, 3D and costings

Open the House Planner

Site Planner

Boundaries, buildings and site coverage

Open the Site Planner

Trade calculators

Concrete, tiling, painting, and brick and block

See the calculators
Know a tradie who would use this? Share this pageFacebookWhatsAppLinkedInXEmail

Link to us

Find our free tools and guides useful? Add one of these badges to your website. Tap a badge to get the code, then paste it into your site.